![]() I have done as you suggested but it still doesn't appear to work. Safesys-vr.inet6.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden) Inet6.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden) Safesys-vr.inet.0: 12 destinations, 12 routes (12 active, 0 holddown, 0 hidden) + = Active Route, - = Last Active, * = Both ![]() Inet.0: 7 destinations, 8 routes (7 active, 0 holddown, 0 hidden) Route 0.0.0.0/0 next-table show routing-options I can only ping my gateway if I include the "bypass-routing" option to skip the routing show routing-instances I still cannot ping from the SRX console to anything on the web. So I decided to test by removing the public interface out of the routing instance and back into the default instance. With the routing instance I found some oddities such as ntp or dns not working on the box. So I guess I am not completely out of the woods yet. Node Priority Status Preempt Manual Monitor-failures LB Loopback monitoring MB Mbuf monitoringĬF Config Sync monitoring RE Relinquish monitoring GR GRES monitoring HW Hardware monitoring Ge-7/0/2 weight show chassis cluster statusĬS Cold Sync monitoring FL Fabric Connection monitoring System-services run show configuration chassis cluster Route 0.0.0.0/0 next-hop show configuration show configuration security zones security-zone untrust If I issue the command "ping bypass-routing interface reth0.0 address" I can ping the gatewayĭescription "WAN Uplink pair 1 of 2 - partner ge-7/0/0" ĭescription "Trust Interfaces Uplink pair 1 of 2 - partner xe-7/0/17" ĭescription "WAN Uplink pair 2 of 2 - partner ge-0/0/0" ĭescription "Trust Interfaces Uplink pair 2 of 2 - partner xe-0/0/17" ĭescription "WAN Uplink - ge-0/0/0 & ge-7/0/0" ĭescription "Trust Interfaces - xe-0/0/17 & xe-7/0/17" Īddress show configuration routing-instances If I just issue the ping command to my gateway, it says "ping: sendto: No route to host" There is a virtual routing instance to split up mgmt interface routing and everything else because the mgmt interface is configured in the same subnet as a sub interface in another zone. Any traffic from the trust zone to untrust works as intended. I am able to ping,ssh to the ip address assigned to my untrust interface. From the console I cannot ping anything through my public interface such as 8.8.8.8. ![]() Users can vote to kick off an individual.ĭisplays the list of users on the server (use PgUp to scroll up).ĭisplays the list of GUID's of all players on the server.I have weird communication issue on an SRX1500 cluster running Junos 18.1R2.5. Users can vote an admin to control the server. Users can vote on a particular mission to loaded. Users can vote for the mission selection. Unlocks the server, allows new clients to join. Locks the server, prevents new clients from joining. logFile = "server_console.log" Įach of those commands should show a confirmation in the chat channels.Įxecute administration scripting command. Von Outputs into logFile defined in server.cfg as e.g. Works as DebugAnswer for all writes into the console. You launch this debugger, then launch ARMA client, connect to the server, and issue any of the commands.Ĭonsole Send to submitter what's on server console. (one very small and easy to use is available at SysInternals website). You need some debugger capable of catching OutputDebugString running on the client machine #debug userSent offĮach command differs a bit some output to screen, some to log file etc. (since Arma 3 v1.64)ĬheckFile userSent userInfo userQueue totalSent JIPQueueĮach command can be disabled by the use of the off parameter e.g. Shows performance information in the dedicated server console. Shows performance information of the server. Reload server config file loaded by -config option.Īllows you to ban a player. Shuts down and restarts the server after mission ends (since Arma 3 00) Shuts down the server after mission ends (since Arma 3 00) Shuts down and restarts the server immediately (since Arma 3 v1.66) MissionsToServerRestart or MissionsToShutdown threshold, the server may immediately restart/shutdown) Note: this will trigger `missionEnd` (so if server.cfg is set with e.g. Difficulty parameter is optional and if not set, current difficulty is kept.Īllows selection of mission on shown list of available missions (all or those inside missionWhiteList = within server.cfg). Select mission with known name and set the difficulty. Without password only possible if you are listed as an admin in server.cfg#Server_Options ARMA 3 Console Commands, ARMA 3 Server Commands, ARMA 3 Commands, ARMA 3, Console Commands, Server Commands, Commands
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |